"- Umožňuje připojení SATA zařízení (jako jsou například pevné disky, optické mechaniky) na IDE rozhraní


IOI ref.: IDE-SATA07
- pro všechny SATA HDD
- bulk
- Chip:Marvell 88SA8052


IDE-SATA07 is a Parallel ATA to Serial ATA Host mode Bridge Board featuring Marvell 88SA8052 Serial ATA bridge Controller.

IDE-SATA07 is ideally suited for tailgate interface applications for converting Serial ATA device into ATA device. Both ATA and ATAPI modes are supported using the same firmware.
Technical Specifications

Parallel ATA to Serial ATA Bridge Board:

* Serial ATA:
o Compliant with Serial ATA 1.0
o 48-bit sector addressing
* Serial ATA Connector:
o Signal + Power (7+15 pin) Female Type Connector
* Parallel ATA:
o Ultra ATA/133 Parallel Interface
o 48-bit sector addressing
o Jumper for selecting Master and Slave
* Parallel ATA Connector:
o Male IDC 2X20 pin Connector
* Transfer Rate:
o Supports PIO and DMA modes
o Supports bus master DMA at 1.5Gbps burst rate
* DC Power Connector:
o IDE Big 4-pin power connector
* LEDs
o Power LED
o SATA PHY Ready LED
o Activity LED (Pin Header 2pin Pitch=2.54mm)
"

 "- Umožňuje připojení SATA zařízení (jako jsou například pevné disky) na IDE rozhraní
Pozn.: K opačnému připojení (IDE zařízení na SATA rozhraní) použijte kód 322163

IOI ref.: IDE-SATA01
- pro všechny SATA HDD
- bulk
- Chip:Marvell 88SA8040


Both ATA and ATAPI devices are supported using the same firmware.
It allows SATA drives (Master or Slave) to be connected to ATA host controller. IDE-SATA01 provides the perfect solution for legacy ATA host controller to attach new SATA devices.

Specification
• Compliant to Serial ATA specification 1.0
• Ultra ATA/133 Parallel interface
• 4-pin FDD Power connector
• Jumper for selecting Master and Slave
• Supports PIO and DMA modes
• Chipset: Marvell 88SA8040
• Dimension 10.09 x 2.54 cm
• For Windows 98SE/ME/2000/2003/XP, Mac OS 9.1 or higher and Linux

System requirements
• a free IDE port
• Windows 98SE/ME/2000/2003/XP, Mac OS 9.1 or higher and Linux

Package content
• SATA- IDE converter
• 4-pin power cable
"

 "Specifikace
Host Bus: 1-lane 2.5 Gb/s PCI Express
Number of Ports: One eSATA and One Internal SATA ports
Boot ROM: Non
Low Profile PCI Form Factor: Yes

Introduction
The SATA2-PCIE1x21 is a two ports Serial ATA II to 1-lane 2.5 Gb/s PCI Express Host Adapter. The SATA2-PCIE1x21 is designed to provide two ports Serial ATA II connectivity (Serial ATA Generation 2 transfer rate of 3.0 Gb/s).
The SATA2-PCIE1x21 supports both AHCI and Legacy IDE controller to increase system feasibility, including Native Command Queuing (NCQ), hot plugging, ATAPI device supporting, programmable output swing control to fit SATA II Gen2i and Gen2m (External SATA Connection, eSATA).


Technical Specification
Compliance
Compliant with Serial ATA AHCI (Advanced Host Controller Interface) Spec. Revision 1.0
Compliant with Bus Master Programming interface for IDE ATA Controllers Revision 1.0
Compliant with PCI Express Bus Spec. Revision 1.0a
Compliant with Serial ATA High Speed Serialized AT Attachment Spec. Revision 1.0a
Compliant with Serial ATA II: Extensions to Serial ATA 1.0a Revision 1.1
Compliant with Gen2i and Gen2m Serial ATA II: Electrical Spec. Revision 1.0
PCI Express Features
Supports 1-lane 2.5 Gb/s PCI Express
Internal native interface to 1-port
All registers accessible in unified memory space
Supports a slave SMBus interface (follow System Management Bus Specification Revision 1.1)
Serial ATA Features
Supports Serial ATA Generation 2 transfer rate of 3.0 Gb/s
Supports SATA II Gen2i and Gen2m (External SATA Connection, eSATA)
Supports Native Command Queuing (NCQ)
Supports Hot Plugging

Systémové požadavky
PC with 1-lane 2.5 Gb/s PCI Express slot
Windows 2000/XP and Windows Server 2003
Drivers: Drivers for Windows 2000/XP and Windows Server 2003 /win7
Mac OS 10.4.8 or later (No driver need)

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.
"

 "- externí zdroj 12V/3A AC/DC
- bez přívodního kabelu (IEC-320-C8 (2241EC52))
- 100-240V 0,8A -

- geeignet für die FW-Repeater Art. 61572(1394R3A) bzw. 61638 (FW-UTPS400) und 61666


Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.

"

 "The Delock PCI card powered by IOI expands your PC by three external FireWire 400 Ports. You can connect FireWire devices like external enclosure, digital camera, camcorder, etc. to the card.

Specification
• IOI item number: IOI-4343T
• 3x external FireWire IEEE 1394a ports
• 1x mini 4pin DC +12 V power connector
• IEEE 1394a to PCI controller: Texas Instruments TSB43AB23
• Data transfer rate up to 400 Mb/s
• 32-bit PCI standard 2.2

System requirements
• Windows 98SE/ME/2000/XP/Vista/7, Mac OS 8.6 or above, Linux 2.4.x
• PC with one free PCI Slot

Package content
• PCI card

Package
• Box"

 "This FireWire card by IOI expands your PC by two external and one internal FireWire A port. You can connect several FireWire devices like e.g. external enclosures with internal hard disk or CD drive, camcorder, internal FireWire devices etc. to the card.

Specification
• IOI item number: FW-PCI3201
• 2 x external FireWire A (IEEE 1394a)
• 1 x internal FireWire A (IEEE 1394a)
• Low profile PCI form factor
• Data transfer rate up to 400 Mb/s
• Chipset: Texas Instruments TSB43AB23
• 1 x internal 4 Pin Molex 12 V power connector

System requirements
• Window 98 SE/Me/2000/XP/Vista/7, Mac OS 8.6 or higher, Linux 2.4.X
• One free PCI card slot

Package content
• PCI card
• Low profile bracket

Package
• White box

- Záslepka do slotu pro low profile je dodávána jako samostatné příslušenství"

 "Specifikace
-2-port Serial ATA to PCI Express Host Adapter with Silicon Image Sil3132 Serial ATA Host Controller
-PCI Express Card x1 to 2x SATA Ports
-Supports 1-lane 2.5 Gb/s PCI Express
-Chipset: Silicon Image Sil3132
-Data transfer rate: Serial-ATA 3.0 GB/s
-For Windows 2000/XP/2003/ Linux 2.6, Mac OSx

Sytémové požadavky
-volný PCI Express Slot
-Windows 2000/XP/2003/ Linux 2.6, Mac OSx

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.
"

 "Host Bus: 1-lane 2.5 Gb/s PCI Express
Number of Ports: One External & Three Internal SATA ports + One Internal PATA ports
Form Factor: Standard Type
Boot ROM: Yes

Introduction
SATA2-PCIE1x12 is a multiple port Serial ATA (SATA)/Parallel ATA (PATA) to PCI Express (PCIE) Host Adapter.
SATA2-PCIE1x11 takes advantages of the 2.5 Gb/s burst rate of 1-lane PCI Express bus and the Serial ATA Generation 2 transfer rate of 3.0 Gb/s (300 MB/s) interface.
This solution provides full PCI Express and Serial ATA (SATA)/Parallel ATA (PATA) functionality and performance.
SATA2-PCIE1x12 delivers the performance and connectivity required for servers and I/O demanding applications such as CD-ROM servers, Video-On-Demand, database servers, workstations, high-end desktops, software RAID sub systems, and image systems.

SATA2-PCIE1X12 supports a high reliable and extremely fast variety of storage applications (RAID 0, 1, 10, 5 and JBOD).

Technical Specification
PCI Express 1.0a compliant - Supports 1-lane 2.5 Gb/s PCI Express interface
PCI Express Programming interface
Compatibility mode via PCI I/O access for legacy host software
Enhanced Mode for SATA ports via Enhanced Mode Registers.
Enhanced Mode for PATA port via Enhanced Mode Registers.
Supports up to 2Mbit external Flash for option ROM or Boot ROM
Supports SPI Flash Interface for retrieving boot code and vendor specific PCI Configuration content.
Supports TWSI EEPROM interface for retrieving vendor specific PCI Configuration content.
Serial ATA (SATA) specification 2.5 compliant.
Supports SATA PHY 3.0 Gb/s with speed negotiation to SATA 1.5Gb/s.
Supports electrical specifications of Gen1i, Gen1m, Gen1x, Gen2i, Gen2m, Gen2x, and usage models of eSATA and xSATA
Supports four independent Serial ATA ports
Serial ATA (SATA) protocols over SATA ports.
ATA and ATAPI commands
Native Command Queuing (NCQ)
Hot Plug
Port Multiplier
Supports SATA Port Selector Switching
Parallel ATA (PATA) protocols over PATA port.
Supports one Parallel ATA port
ATA and ATAPI commands
All modes of PIO, Multiword DMA, and Ultra-DMA (up to 150MB/s)
Tagged Command Queuing (TCQ) with 32 outstanding commands per port
Master and Slave configuration (over PATA port)
Supports interrupt Coalescing over SATA and PATA ports in Enhanced Mode.
Supports SMBus for communication with Hardware Monitoring ICs.

Computer Platfrom
PC with 1-lane 2.5 Gb/s PCI Express slot
Operating System Requirements
Windows 2000/XP/Windows Server 2003/Vista

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.
"

 "1394R-B2 is a standard IEEE1394b repeater, extending your signal an additional 4.5 meters. It's easy to setup and there is no configuration necessary, like all IEEE1394 compliant hardware.

Description
This FW-repeater by IOI is made for extending your signal up to 4,5m for cable extension of FireWire cable.

Specification
- 2 Port FireWire-B Repeater (9pin)
- Signal extension up to 4,5m
- Chip: Texas Instruments TSB81BA3D
- Data transfer rate: up to 800Mbps
- 1394 Bus powered: DC 8V~33V, 1.35A
- Application for cable extension
- Size: 7,35 x 2 x 3,15cm (W/L/H)

Technical Specification
* Fully Supports Provisions of IEEE P1394b Revision 1.33+ at 1-Gigabit Signaling Rates
* Fully Supports Provisions of IEEE 1394a.2000 and 1394.1995 Standard for High Performance Serial Bus
* Fully Interoperable With Firewire., i.LINK., and SB1394., Implementation of IEEE Std 1394
* PHY: TI. TSB81BA3D
* 1394 Bus Transfer Rate: 100 / 200 / 400 /800 Mbps
* Power-Down Features to Conserve Energy
* Low-power Sleep Mode
* Device Interface: Provides Two Fully Backward Compatible, (1394a.2000 Fully Compliant) Bilingual P1394b Cable Ports at up to 800 Megabits per Second (Mbits/s)
* 1394 Bus Powered: DC 8V~33V, max. 1.35A
* Connectors:
o Two Bilingual Cable Port with Jackscrew

Physical Dimensions
* 7.35cm (W) x2cm (L) x3.15cm (H)

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.

"

 "Highlights
* Host Bus: 1-lane 2.5 Gb/s PCI Express
* Eight (8) isochronous transmit/receive contexts
* Deep 8 Kbyte isochronous transmit/receive FIFOs
* Complies with 1394 OHCI draft 1.2
* Three external 1394 ports
* Bilingual ports with Screw Holes for thumbscrew locking Type 1394b Cable

The FWB-PCIE1X21A combines an OHCI (Open Host Controller Interface) and a high-performance, standards-compliant PCI Express 1.1 host system interface to provide S800 1394b-2002 compliant throughput in a small PCB (Printed Circuit Board) and low power dissipation.

MultipleVCs (Virtual Channels) on the PCI Express link provide native support for QoS (Quality of Service) transmission for real-time and multimedia applications in a standards-based framework, ensuring compatibility with current and future operating systems. Active-state power management allows dynamic power management during periods of reduced network activity.
Technical Specifications
PCI Express:
* Designed for compliance with PCI Express.
* Multiple virtual channel (VC0,VC1 ) support fordiffe-rentiating 1394 isochronous traffic.
* Supports eight user-programmable traffic classes.
* 64-bit and 32-bit platform support.
* Interrupts via legacy INTx interface or message sig-naled interrupt (MSI).
* Supports PCI Express clock power management viaCLKREQN signal for form factors that support thisprotocol.
* Supports all linkpowermanagement states (L0,L0s,L1,andL2/L3) and active state power management(ASPM).
* Supports wake-up from a low-power state via in-bandbeacon signaling and side-band WAKE_N signal.

OHCI (Open Host Controller Interface)
* Enhanced with the OHCI 1.2 draft specification for 1394b-2002 PHY full operational compliance.
* OHCI 1.0 backwards compatible. Configurable via EEPROM to operate in either OHCI 1.0 or OHCI 1.1 mode.
* 8 Kbyte isochronous transmit FIFO.
* 4 Kbyte asynchronous transmit FIFO.
* 8 Kbyte isochronous receive FIFO.
* 8 Kbyte asynchronous receive FIFO.
* Dedicated asynchronous and isochronous descriptor-based DMA engines.
* Eight isochronous transmit contexts.
* Eight isochronous receive contexts.
* Supports parallel processing of incoming physical read and write requests.
* Supports up to 48-bit addressing per OHCI specifica-tion for the physical DMA transfers.

1394b-2002 Link
* Cycle master and isochronous resource manager capable.
* Supports 1394a-2000 and 1394b-2002 acceleration features.

1394b-2002 PHY
* Provides three IEEER 1394b-2002 compliant ports sup-porting 1394b-2002 speeds of 800 Mbits/s and 400Mbits/s while maintaining backward compatibility to IEEE 1394a-2000 speeds of 100 Mbits/s, 200Mbits/s, and 400 Mbits/s over 4.5 m copper.
* Fully supports provisions of IEEE 1394a-2000 and 1394-1995 standards for high-performance serial bus.
* Link is not required for hub operation.
* Supports extended BIAS_HANDSHAKE time for enhanced interoperability with camcorders.
* Does not require external filter capacitor for PLL.
* Supports arbitrated short bus reset to improve utiliza-tion of the bus.
* Supports ack-accelerated arbitration and fly-by concat-enation.
* Supports PHY pinging and remote PHY access pack-ets.
* Fully supports suspend/resume.

Reports cable power fail interrupt when voltage at CPS ball falls below 7.5 V.

Number of Ports:
* Two Bilingual ports with Screw Holes for thumbscrew locking Type 1394b Cable+ One Firewire 1394a Cable Port

Bus Power Connector:
* Big IDE 4-pin DC Power Connector

Operating System Requirements
* Windows 2000/XP//7 and Windows Server 2003
* Mac OS 10.4.8 or later
* Linux 2.6.X

Certifications
* CE Test: Pass
* FCC Test : Pass
* VCCI Test: Pass
* RoHS Test : Pass

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.

"

 "Specifikace
- PCI Express Host Adapter na 3 porty OHCI 1.1 kompatibilní IEEE-1394B
- PCI Express x1
- 2+1 FireWire-B porty (2 x externí, 1 x interní)
- čipová sada: Agere/LSI FW643
- rychlost přenosu dat: 800Mbps
- Bus power konektor: IDE 4-pin DC napájecí konektor
- pro Windows 2000/XP, Server2003, MacOS 10.4.8 nebo vyšší, Linux 2.6
- Standard- a LowProfile záslepka slotu součástí dodávky

OHCI (Open Host Controller Interface)
Enhanced with the OHCI 1.2 draft specification for 1394b-2002 PHY full operational compliance.
OHCI 1.0 backwards compatible. Configurable via EEPROM to operate in either OHCI 1.0 or OHCI 1.1 mode.
8 Kbyte isochronous transmit FIFO.
4 Kbyte asynchronous transmit FIFO.
8 Kbyte isochronous receive FIFO.
8 Kbyte asynchronous receive FIFO.
Dedicated asynchronous and isochronous descriptor-based DMA engines.
Eight isochronous transmit contexts.
Eight isochronous receive contexts.
Supports parallel processing of incoming physical read and write requests.
Supports up to 48-bit addressing per OHCI specifica-tion for the physical DMA transfers.


1394b-2002 Link
Cycle master and isochronous resource manager capable.
Supports 1394a-2000 and 1394b-2002 acceleration features.

1394b-2002 PHY
Provides three IEEER 1394b-2002 compliant ports sup-porting 1394b-2002 speeds of 800 Mbits/s and 400Mbits/s while maintaining backward compatibility to IEEE 1394a-2000 speeds of 100 Mbits/s, 200Mbits/s, and 400 Mbits/s over 4.5 m copper.
Fully supports provisions of IEEE 1394a-2000 and 1394-1995 standards for high-performance serial bus.
Link is not required for hub operation.
Supports extended BIAS_HANDSHAKE time for enhanced interoperability with camcorders.
Does not require external filter capacitor for PLL.
Supports arbitrated short bus reset to improve utiliza-tion of the bus.
Supports ack-accelerated arbitration and fly-by concat-enation.
Supports PHY pinging and remote PHY access pack-ets.
Fully supports suspend/resume.
Reports cable power fail interrupt when voltage at CPS ball falls below 7.5 V.

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.

"

 "FWB-PCI3202B

-3x FW-B 800 externí
-Chip: Texas Instr. TSB83AA23 -33-MHz / 32-Bit
PCI-Power: 3,5" IDE 4pin
- Windows 2000/XP/Vista, MacOS 10.4. nebo vyšší, Linux Kernel 2.6.23 nebo vyšší

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.

Highlight
* 32-bit PCI Host interface
* Three External Bilingual (1394b) connectors (with screw lock)
* Big IDE 4-pin DC Power Connector for supplying power to the 1394 Bus

Introduction
FWB-PCI3202B is a three port OHCI 1.1 Compliant FireWire 800 (IEEE-1394b) PCI Host Adapter featuring Texas Instruments OHCI 1.1 Compliant FireWire 800 (IEEE-1394b) Single Chip Host Controller.

Technical Specification
Host Bus:
* 33-MHz/32-Bit PCI Interface
* 3.3-V and 5-V PCI Signaling Environments

IEEE 1394 Std Support:
* Fully Supports Provisions of IEEE P1394b Revision 1.33+ at 1-Gigabit Signaling Rates
* Fully Supports Provisions of IEEE 1394a.2000 and 1394.1995 Standard for High Performance Serial Bus
* Fully Interoperable With Firewire., i.LINK., and SB1394., Implementation of IEEE Std 1394

1394 Bus Transfer Rate:
Provides three fully backward-compatible, (IEEE Std 1394a-2000 fully compliant) Bilingual IEEE Std 1394b-2002 cable ports at S100/S200/S400/S400B/S800 megabits per second (Mbits/s).

IEEE-1394 to PCI Controller
Texas Instruments TSB83AA23

DV and DA Enhancement:
* Digital Video and Audio performance enhancements.
* Extended resume signaling for compatibility with legacy DV components.

Power Management :
D0, D1, D2, and D3 power states and PME events per the PCI Bus Power Management Interface Specification

Number of ports:
* FWB-PCI3202B: Three External Bilingual Ports (with screw lock)

Bus Power Connector:
Big IDE 4-pin DC Power Connector

Operating System Requirements
* The 1394b function (host driver) is supported (built in) by the following OS:
o Windows 2000 SP4 or later
o Windows XP SP2 or later
o Windows Vista SP1 or later
o Mac OS 10.4 or later
o Linux kernel 2.6.23 or later.

"

 "* Host Bus: 1-lane 2.5 Gb/s PCI Express
* Eight (8) isochronous transmit/receive contexts
* Deep 8 Kbyte isochronous transmit/receive FIFO’s
* Complies with 1394 OHCI draft 1.2
* Three external 1394 ports
* Bilingual ports with Screw Holes for Jackscrew Type Plug Cable

The FWB-PCIE1X21B combines an OHCI (Open Host Controller Interface) and a high-performance, standards-compliant PCI Express 1.1 host system interface to provide S800 1394b-2002 compliant throughput in a small PCB (Printed Circuit Board) and low power dissipation.

MultipleVCs (Virtual Channels) on the PCI Express link provide native support for QoS (Quality of Service) transmission for real-time and multimedia applications in a standards-based framework, ensuring compatibility with current and future operating systems.
Active-state power management allows dynamic power management during periods of reduced network activity.

Technical Specification
PCI Express:
* Designed for compliance with PCI Express.
* Multiple virtual channel (VC0,VC1 ) support fordiffe-rentiating 1394 isochronous traffic.
* Supports eight user-programmable traffic classes.
* 64-bit and 32-bit platform support.
* Interrupts via legacy INTx interface or message sig-naled interrupt (MSI).
* Supports PCI Express clock power management viaCLKREQN signal for form factors that support thisprotocol.
* Supports all linkpowermanagement states (L0,L0s,L1,andL2/L3) and active state power management(ASPM).
* Supports wake-up from a low-power state via in-bandbeacon signaling and side-band WAKE_N signal.

OHCI (Open Host Controller Interface)
* Enhanced with the OHCI 1.2 draft specification for 1394b-2002 PHY full operational compliance.
* OHCI 1.0 backwards compatible. Configurable via EEPROM to operate in either OHCI 1.0 or OHCI 1.1 mode.
* 8 Kbyte isochronous transmit FIFO.
* 4 Kbyte asynchronous transmit FIFO.
* 8 Kbyte isochronous receive FIFO.
* 8 Kbyte asynchronous receive FIFO.
* Dedicated asynchronous and isochronous descriptor-based DMA engines.
* Eight isochronous transmit contexts.
* Eight isochronous receive contexts.
* Supports parallel processing of incoming physical read and write requests.
* Supports up to 48-bit addressing per OHCI specifica-tion for the physical DMA transfers.

1394b-2002 Link
* Cycle master and isochronous resource manager capable.
* Supports 1394a-2000 and 1394b-2002 acceleration features.

1394b-2002 PHY
* Provides three IEEER 1394b-2002 compliant ports sup-porting 1394b-2002 speeds of 800 Mbits/s and 400Mbits/s while maintaining backward compatibility to IEEE 1394a-2000 speeds of 100 Mbits/s, 200Mbits/s, and 400 Mbits/s over 4.5 m copper.
* Fully supports provisions of IEEE 1394a-2000 and 1394-1995 standards for high-performance serial bus.
* Link is not required for hub operation.
* Supports extended BIAS_HANDSHAKE time for enhanced interoperability with camcorders.
* Does not require external filter capacitor for PLL.
* Supports arbitrated short bus reset to improve utiliza-tion of the bus.
* Supports ack-accelerated arbitration and fly-by concat-enation.
* Supports PHY pinging and remote PHY access pack-ets.
* Fully supports suspend/resume.

Reports cable power fail interrupt when voltage at CPS ball falls below 7.5 V.

Number of Ports:
* Three Bilingual P1394b Cable Ports with Screw Holes for Jackscrew Type Plug Cable

Bus Power Connector:
* Big IDE 4-pin DC Power Connector

Operating System Requirements
* Windows 2000/XP and Windows Server 2003
* Mac OS 10.4.8 or later
* Linux 2.6.X

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.

"

 "FWB-PCI02

-2x FW-B port
-IEEE1394 to PCI Controller: Texas instruments TSB82AA2
- s 4pin DC a 12V napájecím konektorem
-Windows 89/SE/ME, 2000,XP, MacOS8.6 a vyšší, Linux 2.4x

PCI 2.x Compliant
Universal PCI interfaces compatible with 3.3-V and 5-V PCI signaling environments.
33-MHz/64-bit and 33-MHz/32-bit selectable PCI interface.

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.
"

 "The Delock FireWire PCI card by IOI expands your PC by four external FireWire A ports. You can connect several FireWire devices like e.g. external enclosures with integrated hard disk or CD drive, camcorder etc. to the card.

Specification
• IOI item number: IOI-4601-22
• 4 x external FireWire A (IEEE 1394a)
• 1 x intern Bus power connector with mini 4 Pin DC + 12 V power connector
• Chipset: 2 x TI TSB43AB22A
• Data transfer rate up to 800 Mb/s (400 Mb/s / Channel) per Port
• 32-Bit PCI standard 2.2
• Supports OHCI 1.1 standard
• Dual channel OHCI

System requirements
• Windows 98SE/Me/2000/XP/Server-2003/Vista/7, Mac OS 10.5 or higher, Linux Kernel 2.6
• One free PCI slot

Package content
• PCI Express Card 4x external FireWire A
• Y-cable power Molex > Molex 4 Pin + 31/2 FDD

Package
• Antistatic cover

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.
"

 "IOI-4601-21

The Delock FireWire PCI card by IOI expands your PC by two external FireWire A ports. You can connect several FireWire devices like e.g. external enclosures with integrated hard disk or CD drive, camcorder etc. to the card.

Specification
• IOI item number: IOI-4601-21
• 2 x external FireWire A (IEEE 1394a)
• 1 x intern Bus power connector with mini 4 Pin DC + 12 V power connector
• Chipset: 2 x TI TSB43AB22A
• Data transfer rate up to 800 Mb/s (400 Mb/s / Channel) per Port
• 32-Bit PCI standard 2.2
• Supports OHCI 1.1 standard
• Dual channel OHCI

System requirements
• Windows 98SE/Me/2000/XP/Server-2003/Vista/7, Mac OS 10.5 or higher, Linux Kernel 2.6
• One free PCI slot

Package content
• PCI Express Card 4x external FireWire A
• Y-cable power Molex > Molex 4 Pin + 31/2 FDD

Package
• Antistatic cover

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.

"

 "Specifikace
One to Five SATA Port Multiplier (SCSI I 50pin Low Density Centronics Connector Form Factor)

Highlight
1-to-5 SATA Port Multiplier
Full support for FIS-based switching and command-based switching SATA host controllers
Supports host and device link rates of 1.5Gbps and 3Gbps with auto-negotiation
Supports host control of hard disk drive staggered spin-up
All ports support hot plug and extended (48 bit LBA) drive capability.
ATAPI support
Features independent 8 KByte FIFO per Device Serial ATA channel for reads and writes
Host and device status and activity LEDs
Coupling with SATA2-PCIE02 or SATA2-PCIX01 to support RAID Function (RAID 0, 1, 5, 10, Concatenated and JBOD).

SPMH3726 is 1-to-5 SATA Port Multiplier designed to provide a high performance link between a single SATA host port and 5 SATA device ports. With its unique data aggregation capability and 3Gbps serial link capability, the SPMH3726 is able to take full advantage of 3Gbps host link bandwidth and FIS-based switching host controllers by bundling together data from device ports and sending it over the 3Gbps host link. Additionally, the feature-rich SPMH3726 supports all the port multiplier related SATA II extensions allowing system designers to exploit the full potential of SATA in their storage solutions.

The SPMH3726 supports host and device link rates of 1.5Gbps and 3Gbps with auto-negotiation allowing system designers to utilize 3Gbps host links with today??s 1.5Gbps hard drives, and to futureproof designs for the emergence of 3Gbps SATA hard drives. Additionally, the SPMH3726 contains a SATA enclosure management bridge (SEMB) to pass in-band enclosure management information between the host and an enclosure management device. Other important features include, programmable high drive capability for backplane and external applications, asynchronous notification to eliminate the need for host polling to determine if a device has been added or removed, and hot plug support.

Coupling with proper host controllers such as Silicon Image Sil3124, Sil3132 and Marvell 88SE6145, SPMH3726 - SATA II port multiplier, a high reliable and extremely fast variety of storage applications (RAID 0, 1, 5, 10, Concatenated and JBOD).

MH3726 delivers the performance and connectivity required for servers and I/O demanding applications such as CD-ROM servers, Video-On-Demand (digital content and high-definition video), database servers, workstations, high-end desktops, software RAID sub systems, and image systems.

Technical Specification
Host Port
- Supports one SATA host port, 1.5Gb/s and 3Gb/s
- Hot Plug support
- Supports Async Notification
- SATA Port Multiplier spec. compliant
- Supports PM aware hosts and non-PM aware
- Two detailed system status LEDs
- eSATA signal level suppport (1m and 2m PHY compliant)
Device Port
- Four SATA device ports, 1.5Gb/s and 3Gb/s
- Hot Plug support
- SATA Port Multiplier spec. complaint
- Compatible with NCQ drives
- Two LEDs for detailed status per port
- eSATA signal level support (1m and 2m PHY compliant)
System Features
- Five status LEDs for system functions
- Works without BIOS updates
- Max. performance greater than 220MB/s (RAID 0)
- Enclosure Management SEMB (I2C bus) support
- Automatic bad sector remapping
- OS Agnostic operation
- Bootable arrays and staggered spin-ups
- ATAPI device support in PM mode
- Spread Spectrum Clocking w/SSC clock
- Event logging from GUI
- Remote monitoring and management
- Email notification
- Manage multiple devices via GUI
- Field-upgradeable firmware

Application
Expansion Storage Bricks
Disk Shelves
Storage Enclosures

It is designed to provide a high performance link between a single SATA2 host port and 5 SATA device ports. With its unique data aggregation and 3Gbps serial link capacity, it supports 5 SATA or SATA2 device with auto-negotiation features over one single eSATA connector.
SPMH3726 is equipped with a "SCSI I 50pin Low Density Centronics Connector" like bracket to be mounted in a standard enclosure to provide the immediate upgrade of your storage system.

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.





"

 "1394R-B4 is a four ports IEEE1394b repeater, extending your signal an additional 4.5 meters. It's easy to setup and there is no configuration necessary, like all IEEE1394 compliant hardware.
Technical Specification

* Fully Supports Provisions of IEEE P1394b Revision 1.33+ at 1-Gigabit Signaling Rates
* Fully Supports Provisions of IEEE 1394a.2000 and 1394.1995 Standard for High Performance Serial Bus
* Fully Interoperable With Firewire., i.LINK., and SB1394., Implementation of IEEE Std 1394
* PHY Chip: TI TSB81BA3D.
* 1394 Bus Transfer Rate: 100/ 200/ 400/ 800 Mbps
* Device Interface: Provides Four Fully Backward Compatible, (1394a.2000 Fully Compliant) Bilingual P1394b Cable Ports at up to 800 Megabits per Second (Mbits/s)
* DC Power input Connector: Walkman-type 2.0 mm DC Jack
* Power Input Range: DC 8V~30V, max. 1.35A
* Power Consumption: Under 1.5 Watts.
* Number of ports: Four Bilingual Cable Port with Jackscrew Lock Holes
* Power LED

Physical Dimensions
* 92(W)x62(D)x20.6(H)mm

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.
bez napájecího zdroje - dodáván samostatně - viz související produkty

"

 "3-port OHCI Compliant Firewire 800 (IEEE 1394b) to PCI Host Adapter featuring Ti TSB83AA23 IEEE 1394 Host Controller (Low Profile PCI Form Factor)

* 32-bit PCI Host interface
* One Internal Bilingual (1394b) Port
* Two External Bilingual (1394b) connectors (with screw lock)
* Big IDE 4-pin DC Power Connector for supplying power to the 1394 Bus
* Low Profile PCI Form Factor
FWB-PCI3203 is a three port OHCI 1.1 Compliant FireWire 800 (IEEE-1394b) to PCI Host Adapter featuring Texas Instruments OHCI 1.1 Compliant FireWire 800 (IEEE-1394b) Single Chip Host Controller.

Technical Specification
Host Bus:
* 33-MHz/32-Bit PCI Interface
* 3.3-V and 5-V PCI Signaling Environments

IEEE 1394 Std Support:
* Fully Supports Provisions of IEEE P1394b Revision 1.33+ at 1-Gigabit Signaling Rates
* Fully Supports Provisions of IEEE 1394a.2000 and 1394.1995 Standard for High Performance Serial Bus
* Fully Interoperable With Firewire., i.LINK., and SB1394., Implementation of IEEE Std 1394

1394 Bus Transfer Rate:
Provides three fully backward-compatible, (IEEE Std 1394a-2000 fully compliant) Bilingual IEEE Std 1394b-2002 cable ports at S100/S200/S400/S400B/S800 megabits per second (Mbits/s).

IEEE-1394 to PCI Controller
Texas Instruments TSB83AA23

DV and DA Enhancement:
* Digital Video and Audio performance enhancements.
* Extended resume signaling for compatibility with legacy DV components.

Power Management :
D0, D1, D2, and D3 power states and PME events per the PCI Bus Power Management Interface Specification

Number of ports:
* FWB-PCI3203: Two External Bilingual Ports (with screw lock) + One Internal Bilingual Port

Bus Power Connector:
Big IDE 4-pin DC Power Connector

Operating System Requirements
* The 1394b function (host driver) is supported (built in) by the following OS:
o Windows 2000 SP4 or later
o Windows XP SP2 or later
o Windows Vista SP1 or later
o Mac OS 10.4 or later
o Linux kernel 2.6.23 or later.

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.
"

 "The Delock PCI Express card powered by IOI expands your PC by two external FireWire 400 ports. You can connect devices like e.g. external enclosure, digital cameras, camcorder, adapter, etc. to the card.

Specification
• IOI item number: FWX2-PCIE10-2
• External: 2x FireWire IEEE 1394A
• Internal: 1x 12V power connector 4-Pin
• 2x IEEE 1394a Single Chip Host Controller (TSB43AB22A)
• Data transfer rate up to 400 Mbps
• Supports OHCI specifications 1.1
• PCI Express x1 Standard
• Supports PCI Express 1.0a specification

System requirements
• Windows 2000/XP/Server-2003/Vista, Mac, Linux 2.6.x
• PC with one free PCI Express Slot

Package content
• PCI Express card

Package
• Box

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.

"

 "The Delock PCI Express card powered by IOI expands your PC by four external FireWire 400 ports. You can connect devices like e.g. external enclosure, digital cameras, camcorder, adapter, etc. to the card.

Specification
• IOI item number: FWX2-PCIE10-4
• External: 4x FireWire IEEE 1394A
• Internal: 1x 12V power connector 4-Pin
• 2x IEEE 1394a Single Chip Host Controller (TSB43AB22A)
• Data transfer rate up to 400 Mbps
• Supports OHCI specifications 1.1
• PCI Express x1 Standard
• Supports PCI Express 1.0a specification

System requirements
• Windows 2000/XP/Server-2003/Vista/7, Mac, Linux 2.6.x
• PC with one free PCI Express Slot

Package content
• PCI Express card

Package
• Box

> Package content: 4Port PCI card Only. 2 Poct PCI Card upon request.

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.
"

 "Pro vytvoření funkční sestavy jsou zapotřebí
2 x 61638, 2 x 41252 a křížený kabel RJ45 potřebné délky


FW-UTPS400 is two FireWire (1394a) to one RJ45 port S400 Repeater
FW-UTPS400 enables 1394 signals to be transmitted and received over Cat5 or Cat6 Unshielded Twisted- Pair (UTP) cable.
FW-UTPS400 is optimized to create long-haul IEEE 1394b-2002 connections over Cat5 or Cat6 at the S400 data rate, but it can also be used at S200 and S100.
FW-UTPS400 also works for Cat5-structured wiring cable that is typically installed in a home or office.

Fully Supports Provisions of IEEE 1394a.2000 and 1394.1995 Standard for High Performance Serial Bus
Fully Interoperable With Firewire, SB1394, DishWire, and i.LINK Implementation of IEEE Std 1394
Fully Supports Provisions of IEEE Std 1394b-2002 at S400B Signaling Rates
Equipped with a multi-rate adaptive equalizer which restore IEEE Std 1394b signals received over Cat 5 or Cat6 Unshielded Twisted Pair (UTP) Cable at 400 Megabits per Second (Mbits/s)
DC Power Connector: Walkman-type 2.0 mm DC Jack
Power Input Range: DC 8V~30V, max. 1.35A
Power & Link LEDs

The Delock repeater by IOI extends a FireWire A connection. Connect you PC or notebook with a RJ45 cable to the repeater to get a maximum extension of 55 m. You can connect several FireWire devices like e.g. external enclosures, digital cameras, camcorder, adapter etc. to the repeater.

Specification
• IOI item number: FW-UTPS400
• Data transfer rate up to 400 Mb/s
• Connection: 2 x FireWire A
1 x RJ45
• Power connection: DC Jack Walkman type 2 mm
• Power input: 8 V ~ 30 V, max. 1,35 A
• LED indicators for power and link

System requirements
• A free FireWire A port

Package content
• Repeater

Package
• Poly bag

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.

"

 "1394R-B5 is a five ports IEEE1394b repeater, extending your signal an additional 4.5 meters. It's easy to setup and there is no configuration necessary, like all IEEE1394 compliant hardware.
Technical Specifications

* Fully Supports Provisions of IEEE P1394b Revision 1.33+ at 1-Gigabit Signaling Rates
* Fully Supports Provisions of IEEE 1394a.2000 and 1394.1995 Standard for High Performance Serial Bus
* Fully Interoperable With Firewire., i.LINK., and SB1394., Implementation of IEEE Std 1394
* PHY Chip: TI TSB81BA3D.
* 1394 Bus Transfer Rate: 100/ 200/ 400/ 800 Mbps
* Device Interface: Provides Four Fully Backward Compatible, (1394a.2000 Fully Compliant) Bilingual P1394b Cable Ports at up to 800 Megabits per Second (Mbits/s)
* Number of ports: Five Bilingual Cable Port (with Jackscrew Lock Holes)
* DC Power input Connector: Walkman-type 2.0 mm DC Jack
* Power Input Range: DC 8V~30V, max. 3A
* Power Consumption: Under 3 Watts.
* IEEE 1394 Power Class::
o 1394R-B5 was designed with 1394 power class 4 (PC0 ~ PC2 = 100).
o 1394R-B5 is a bus-powered device, it could be powered from DC Jack/ FireWire (IEEE 1394) bus and will repeat the power to FireWire (IEEE 1394) bus.
o Power Class Descriptions: Node may be powered from the bus for the PHY only using up to 3W and may also provide power to the bus. The amount of bus power that it provides can be found in the configuration ROM. * Each IEEE 1394 (FireWire) port is protected by one 1.35A/33V Fuse.
* Power LED

Applications
* Cable extension
* Four more ports
* Provide power to the 1394 bus
* Provide a metal bracket for fixing the 1394R-B5.

Physical Dimensions
92 (W) x 62 (D) x 20.6 (H) mm

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.

"

 "Dual Channel 4-port OHCI 1.2 Compliant FireWire 800 (IEEE 1394b) to PCI Express Host Adapter

The FWBX2-PCIE1xE220 is a Dual OHCI 1.2 Compliant FireWire 800 (IEEE 1394b) to PCI Express Host Adapter.

FWBX2-PCIE1xE220 is designed with Two key components.
* 3-Lane, 3-Port PCI Express Switch.
* OHCI 1.2 Compliant IEEE 1394b Single Chip Host Controller.

Utilizing the standard PCI Express Switch, the 3-Lane/3-Port PCI Express Switch provides the most efficient fan-out solution for integrating two OHCI 1.2 Compliant IEEE 1394b Single Chip Host controllers into a small board design. Each OHCI 1.2 Compliant IEEE 1394b Single Chip Host controller takes advantages of 2.5 Gbps burst rate of 1-lane PCI Express bus in both directions and is fully compliant with PCI Express Base specification 1.1. This solution provides full PCI Express and 1394b functionality and performance.

PCI Express:
* Fully compliant with revision 1.1 base specification.
* One virtual channel.
* Eight traffic classes.
* 64-bit and 32-bit platform support.
* PCI compatible Interrupts via legacy INTx emulation

OHCI (Open Host Controller Interface):
* Enhanced with the OHCI 1.2 draft specification for 1394b-2002 PHY full operational compliance.
* OHCI 1.0 backwards compatible. Configurable via EEPROM to operate in either OHCI 1.0 or OHCI 1.1 mode.
* 8 Kbyte isochronous transmit FIFO.
* 4 Kbyte asynchronous transmit FIFO.
* 8 Kbyte isochronous receive FIFO.
* 8 Kbyte asynchronous receive FIFO.
* Dedicated asynchronous and isochronous descriptorbased DMA engines.
* Eight isochronous transmit contexts.
* Eight isochronous receive contexts.
* Supports parallel processing of incoming physical read and write requests.

1394b-2002 PHY:
* Provides three IEEE® 1394b-2002 compliant ports supporting 1394b-2002 speeds of 800 Mbits/s and 400 Mbits/s while main- taining backward compatibility to IEEE 1394a-2000 speeds of 100 Mbits/s, 200 Mbits/s, and 400 Mbits/s over 4.5 m copper.
* Fully supports provisions of IEEE 1394a- 2000 and 1394-1995 standards for high- performance serial bus.
* Link is not required for hub operation.
* Supports extended BIAS_HANDSHAKE time for enhanced interoperability with cam- corders.
* Does not require external filter capacitor
for PLL.
* Supports arbitrated short bus reset to improve utilization of the bus.
* Supports ack-accelerated arbitration and fly-by concatenation.
* Supports PHY pinging and remote PHY access packets.
* Fully supports suspend/resume.

FireWire P1394b Cable Ports :
FWBX2-PCIE1xE220: Four FireWire P1394b Cable Ports
* OHCI 1: Two 1394b Bilingual Ports
* OHCI 2: Two 1394b Bilingual Ports

Power Management:
* Supports PCI Power Management Interface specification (PCI-PM 1.2)
* Supports Advanced Configuration and Power Interface Specification, Revision 2.0 (ACPI) supporting active link state.

Bus Power Connector:
with IDE big 4-pin DC +12V power connector

Operating System Requirements
* Windows 2000, XP, 2003
* Linux 2.6.X
* Mac OS X

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.

"

 "Specifikace
-4 Port FW-B PCI I/O Karte 64-bit
-Data transfer: 100/200/400/800 Mbps
-Bus power: IDE4 -pin DC power connector
-Chip: Texas instruments:TSB82AA2B
-pro Windows 98 SE/ME,2000,XP,2003, Mac OS x nebo vyšší, Linux 2.6x

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.


"

 "IOI Ref. : FWBU2SATA35DMR

Specification
- Raid enclosure FW-B, USB2.0 to SATA
- for 2x SATA HDD 31"
- Ports: USB2.0- B , FW-800, SATA
- RAID 1, RAID 0, JBOD, Span
- Supports SATA and SATA II
- DC power connector: 2mm DC connector
- HDD-Power Connector: 2x 4pin Floppy Type
- 40x40 mm fan
- Aluminium case
- LED for HDD-access and error indicator
- HDD-size= no limit
- For Windows ME/2000/XP/2003, Mac OS 9.1or higher, Linux Mac

System requirement
- A freeUSB2.0-B or FireWire-B Port
- Windows ME/2000/XP/2003, Mac OS 9.1 or higher, Linux Mac

Package content
- Raid enclosure
- Beta 9pin -to- Beta 9pin Cable (2m length)
- A -to-B Typ USB 2.0 (1.5m length)
- AC 100 ~ 240 V zu DC +12V/ 4.16A Power Adapter
- AC power cord
- Screws for 2x 3.5" HDD
- Screw driver
- Manual

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.






"

 "Specifikace
-2x FW 800 Ports and GOF (Duplex LC) to PCI Host Adapter
-Ports: 2x FW-B, 1x GOF
-GOF = Glass optical fiber
-Chip: Texas Instruments TSB82AA2
-Data transfer rate: 800Mbps
-Fiber Optical Port:
1x Agilent HFBR-5911L (DUPLEX LC) Small Form Factor Fiber Optic Transceiver.
Compatible with Specification of IEEE 802.3 Gigabit Ethernet (1.25Gbd) 1000BASE-SX
850nm VCSEL(Vertical Cavity Surface Emitting Laser)
Maximale Verbindungslänge:
– 220 m Links in 62.5/125 µm MMF 160 MHz*km Cables
– 275 m Links in 62.5/125 µm MMF 200 MHz*km Cables
– 500 m Links in 50/125 µm MMF 400 MHz*km Cables
– 550 m Links in 50/125 µm MMF 500 MHz*km Cables
Laser AEL Class 1 (eye safe) per:
–US 21 CFR(J)
–EN 60825-1 (+All)-Bus power connector: IDE- 4pin DC +12V Power connector

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.

"

 "2-port OHCI Compliant FireWire 800 (IEEE 1394b) & GOF (DUPLEX LC) to PCI-Express Host Adapter featuring Ti TSB82AA2 IEEE 1394 Host Controller
GOF= Glass optical fiber(Glasfaser)

The FWB1GLC-PCIE10 is a 2-port FireWire800 (IEEE 1394b) & GOF(DUPLEX LC) to PCI Express Host Adapter.

FWB1GLC-PCIE10 is designed with three key components.

* PCI Express to PCI Bus Translation bridge.
* Texas Instruments TSB82AA2 --- IEEE 1394b OHCI-Lynx Controller.
* Texas Instruments TSB81BA3 --- IEEE 1394b 3-port Cable Transceiver/Arbiter.

The PCI Express to PCI local bus translation bridge takes advantages of the 2.5 Gb/s burst rate of 1-lane PCI Express bus and the PCI bus interface is connected to a IEEE 1394b OHCI-Lynx host controller and a three-port 1394b PHY. This solution provides full PCI Express and 1394b&GOF functionality and performance.
Technical Specification
PCI Express and PCI:
* Supports 1-lane 2.5 Gb/s PCI Express.
* Utilizes 100-MHz Differential PCI Express Common Reference Clock
* Fully Compliant with PCI Express Base Specification, Revision 1.0a
* Packetized serial traffic with PCI Express split completion protocol
* Automatic retry of bad packets
* 8b/10b signal encoding
* In-band interrupts and messages
* Support of message signaled interrupts
* Fully Compliant with PCI Local Bus Specification, Revision 3.0
* PCI Bus Power Management Interface r1.1 Compliant

IEEE 1394 Std Support:
* Fully Supports Provisions of IEEE P1394b Revision 1.33+ at 1-Gigabit Signaling Rates
* Fully Supports Provisions of IEEE 1394a.2000 and 1394.1995 Standard for High Performance Serial Bus
* Fully Interoperable With Firewire., i.LINK., and SB1394., Implementation of IEEE Std 1394

1394 Bus Transfer Rate:
* Provides two IEEE Std 1394b-2002 fully compliant cable ports at 100/200/400/800 megabits per second (Mbits/s).

Fiber Optical Port:
* With one Agilent HFBR-5911L (DUPLEX LC) Small Form Factor Fiber Optic Transceiver.
* Compliant with Specifications for IEEE 802.3 Gigabit Ethernet (1.25Gbd) 1000BASE-SX
* 850nm VCSEL(Vertical Cavity Surface Emitting Laser)
* Maximum link lengths:
V 220 m Links in 62.5/125 gm MMF 160 MHz*km Cables
V 275 m Links in 62.5/125 gm MMF 200 MHz*km Cables
V 500 m Links in 50/125 gm MMF 400 MHz*km Cables
V 550 m Links in 50/125 gm MMF 500 MHz*km Cables
* Laser AEL Class 1 (eye safe) per:
VUS 21 CFR(J)
VEN 60825-1 (+All)

Number of Ports:
External:
* Two Bilingual 9pin with Jackscrew holes
Provides Two Fully Backward Compatible, (1394a.2000 Fully Compliant) Bilingual P1394b Cable Ports at up to 800 Megabits per Second (Mbits/s)
* One GOF(DUPLEX LC) Port

Power Management:
D0, D1, D2, and D3 power states and PME events per the PCI Bus Power Management Interface Specification

Bus Power Connector:
Big IDE 4-pin DC Power Connector

Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.

"